NC Twin Roll Feeder : TRF Series
This series is designed for short materials. Its characteristics are shown below.
- The machine is equipped with a C-type frame. A workpiece can be supplied from the machine front.
- With a sliding plates as standard, the machine position is possible to adjust to the inside or outside of a bolster (by manual operation).
- The main body and controller unit are integrated and it saves space.
Maximum stamp speed is 200spm and maximum matrial thickness is up 3.2mm. Two models are provided for vary material width.
The lower movies are about this product utilized for processing short materials. Click screen and the movie will start. It has sounds, so please be attentive to volume.
You can watch after download. Click and store the links below.
Product Specification
For basic specification, prease refer below table.
| TRF202 | TRF302 |
|---|
| Limit of Material | Max. Width | 200mm | 300mm |
|---|
| Max. Thickness | 3.2mm |
|---|
| Max. Stamp Speed | 200spm |
|---|
| Material Feeding | Method | ローラ + Servomotor |
|---|
| Feed Length | 999.99mm Max.
Adjusted by 0.01mm unit. |
|---|
| Feed Speed | 10段階設定 *1 |
|---|
Standard Load
Width / Thickness
コイル材 | 50/3.2mm
200/1.6mm | 50/3.2mm
300/1.6mm |
|---|
Standard Load
Width / Thickness
短尺材 | 200/3.2mm
最大15kg | 300/3.2mm
最大15kg |
|---|
| Material Pressing | Method | Spring |
|---|
| Pressing Capacity | 1700N
Adjusted by screws. |
|---|
| Material Releasing Method | Air Cylinder |
|---|
| Sheet Mode | 取り数 | 最大999
1単位設定 |
| Discharge Length | 最大990mm
10mm単位設定 |
| Required Power Supply | Three-phase AC200V±10%, 50/60Hz |
|---|
| Product Weight | Main Body 43kg X 2
Controller 5kg | Main Body 53kg X 2
Controller 5kg |
|---|
*1 加速度設定はありません。加速時間が一定になるように自動調節されます。
Feeding performance of TRF202 and TRF302 is shown in below table.
Stamp Speed
[spm] | Max. Feed Length [mm] |
|---|
Feed Angle
180° | Feed Angle
210° |
| 200 | 22 | 31 |
|---|
| 180 | 28 | 39 |
|---|
| 160 | 36 | 51 |
|---|
| 140 | 48 | 68 |
|---|
| 120 | 68 | 94 |
|---|
| 100 | 100 | 139 |
|---|
| 80 | 160 | 221 |
|---|
| 60 | 283 | 367 |
|---|
| 40 | 534 | 660 |
|---|
Controller
短尺材を取り扱うモードとコイル材を取り扱うモードがあり、動作が異なります。
Sheet Mode
- Indicator of Feed Length.
- Count of stamp by discharge.
- Indicator of rest stamp.
- Discharge length (cm).
Coil Mode
- Indicator of feed length of left machine.
- Indicator of feed length of right machine.
※Set the digital switch of "press shot count" to 000.
お知らせ
- 2010年3月1日
- 2006年2月1日
- 電気接続用のコネクタを仕様変更しました。詳細はこちら。
- TRF082、TRF132およびTRF402は2004年8月で生産終了致しました。
