Options

We offer a large number of options. It can be used in combination according to the situation. Please see the price list page for the compatibility of each product with options.

Table of Contents

Remote Box: RC6A
Feed Direction Change : DS6
Feed-During Output : BS6
Feed Completion Output : FF6
Data Bank : MP6
Feed conditions measurement : TC6
Work Shortage Sensor
Pulling Type
Controller Offset
Swing Cover
Special roller
Separate Roll
Apron Roll
Slide Mounting Plate

Remote Box: RC6A

Can be operated at a remote location from main controller. (One Stroke / Inching / Roll Open & Close / Sync Release)
The length of the cable can be selected of 3m or 5m.

The feed speed of one stroke operation by this unit is limited as only inching speed.

For safety, the operations by main controller are prohibited when using RC6A. In addtion, manual operations by RC6A are not allowed while synchronizing with press machine.

❊ We may not be able to respond to products shipped before January 2018.

Feed Direction Change : DS6

This changes the direction of rotation of the roll by the changeover switch. It allows feed direction of the material either pulling or pushing.

it can add second work shortage sensor and change the available sensor by setting.

R20, R30, R40, R50 and J25, is the one-way brake is equipped.
This is when the motor control is OFF, it is intended to hold the material.
But This brake will be removed for the direction switching options and conflicting function.

Feed conplation output unit will be mounting to be stacked on top of the main controller.

Feed-During Output : BS6

And it outputs the signal at the time of material feeding.
It can be used when other peripheral devices and the interlock is required.

Option of conventional products, "Feed master unit" and same press alternating operation is possible by combining it with the "Feed completion output (FF6)".

Feed conplation output unit will be mounting to be stacked on top of the main controller.

Feed Completion Output : FF6

And it outputs the signal at the time of material feeding completion.
It can be used when other peripheral devices and the interlock is required.

The output is enabled or disabled by operation switch and external input.

Option of conventional products, "Feed master unit" and same press alternating operation is possible by combining it with the "Feed-during output(BS6)".

Feed conplation output unit will be mounting to be stacked on top of the main controller.

Data Bank : MP6

99 sets of settings such as "Feed length", "Feed angle" and "Release mode" can be stored (❊).It is possible to call without having to re-enter the feed conditions every time the mold is changed.

And also, a part of 99 settings can be chained. By this means, this unit can perform multi-layer(stage) operation as conventional multi-layer unit. Repeat count on a layer is up to 99. With a combination of DS6 unit, feed direction is changeable.

About multi-layer operation, pleas refer detailed description page.

Feed conplation output unit will be mounting to be stacked on top of the main controller.

It is possible to add output signal and serial communication function at the completion of multistage feed. For details, refer to the explanation page of the serial communication function.

❊ Please note that only 20 sets can be set under the following conditions.

When using MP6 shipped before June 2018.
When MP6 is added to the controller shipped before June 2018.

Feed conditions measurement : TC6

It is an option to automatically enter the feed angle of our feeder and the setting value of press use rotational speed.

In advance, please set the feed signal on the press side.
After that, the feed signal is measured by preliminary operation of the press, and the feed angle of our controller "Feed Angle" and the press use rotational speed "spm" are automatically calculated ( Patent application already).

We recommend it when it is difficult to set it by converting it into a numerical value when driving press with pendulum or irregular motion.

Feed conplation output unit will be mounting to be stacked on top of the main controller.

❊ We may not be able to respond to products shipped before October 2018.

Work Shortage Sensor

It is an optical sensor that detects the material out.
Can adjust the sensitivity of the optical sensor, depending on the environment.

It can be installed in all of the series, but in T series it is limited only when using coil mode and single mode.

Mounting method & mounting position will vary depending on the model.
The picture on the right is one that was Mounting to J06

Added a single output mode for out-of-material sensor signals. Please refer to the detailed explanation page.

Pulling Type

Pulling the material by mounting a feeder to the process side after the press　working.
Do not want to scratch the product.
Prevent the deflection of the thin material caused by feeding pushing the material.
Please select in that case.

Controller Offset

It is an option of J · R series excluding J 06. Slide the controller far away from the press and install. It is effective when it interferes with press etc. when installing the feeder.

J06 is a standard specification.Since the mounting method of the controller differs depending on the model, there is no compatibility of models with parts such as brackets.

Angle laydown controller bracket

By attaching the angle attachment stay with the offset "option" of the controller you can change the angle of the controller to your preferred angle.

It is applicable to J series & R series. In the G series, it is possible to adjust only one step by standard specification.

Please note that there is a danger of interference depending on the controller angle.

Swing Cover

Make the top cover of the feeder body openable and closable. It is effective for roll cleaning and adjustment of separate roller.To avoid interference with the controller when opening and closing the cover, it is a set with the controller offset option.

It is applicable to J series, R series. Although it is not possible to correspond to the H series, there is an option of the RV specification as a similar function. For details, refer to the RV specification in the H series product introduction page.

Special roller

Urethane Roller

It is a roll of urethane resin.

For metal rolls, rolling to materials can be reduced with urethane rolls even with soft materials to be rolled.Also, scratches on materials can be prevented.

For material with less slippage of material and slippery material, feed accuracy may be better than metal roller. Chemical resistance and durability are inferior to standard rolls.

Since the roll release stroke is small in the H series & A-A series, it can not be used because roll deformation occurs.

Silicon roller

It is a roll of silicon resin.

It is superior to non-stickiness, heat resistance and chemical resistance than urethane roll.It is suitable for feeding special materials pasted with film material or adhesive tape.

Because the abrasion resistance is inferior to the urethane roll, the material is liable to slip.

Since the roll release stroke is small in the H series & A-A series, it can not be used because roll deformation occurs.

BBC Roller

A roll treated with blasting and blueing.

The frictional force of the contact surface between the material and the roll is large, and material transport with less slip is possible.

Scratches easily attached to materials. When sending strict materials against scratches, we recommend you to use the option of separate roll, which can escape the central part of the material.

Central clamp Roller

This is an option for A-A series. By adopting a "central clamp roll", it is possible to handle a minimum material width of 50 mm, compared to the minimum material width of the standard roll. However, please note that the transport capacity will change..
Please refer to this document for details.

Separate Roll

Hold the material with two rings that can change the position in the width direction of the material.

It is suitable for escape of Convex of secondary processed products and when protecting materials from scratches.

The adaptation models are as follows.

For the J, R series, swing cover and controller offset options are also required for adjusting the position of the ring.

In case of handling with H series, it becomes correspondence with optional apron bracket detachment type (RV specification).
Also, use the setting so that the value of Acceleration [%] is 80% or less.

R-SRF, J-SRF

Standard assembled specification of separate roll for J series, R series excluding J06.It is written as -SRF after the series name.
The combination of options is as follows.

Upper roll: Separate roll.
Lower roll: Separate roll. * J15/J25 can not correspond.
Roll surface treatment: You can choose from 4 kinds of hard chrome plating / BBC / urethane / silicone.
Swing cover with acrylic window
Controller offset
Material Pressure spring: Spring constant small
（R20-SRF、R30-SRF、R40-SRF、R50-SRF only)

By placing the window of PET material on the swing cover on the top of the feeder body, you can check the state of the roll even with the cover closed.

You can browse the catalog from the download page. If you would like to change the specification of the set, please consult us.

You can see the movie which is processing the material with the SRF specification.Click screen and the movie will start. It has sounds, so please be attentive to volume.&br:※The video is RF20A-SRF of the old model.

Apron Roll

In order to stabilize the coil material, add an extension roll to the material inlet side of the feeder.

The G series are standard specifications.

Slide Mounting Plate

Change the position of the roll feeder. It is possible to bring the roll feeder closer to the mold.

T series assuming use of short material is standard specification.